- 1 What is the use of stub axle?
- 2 What are stub axles made from?
- 3 What are the symptoms of a broken axle?
- 4 What is stub shaft?
- 5 Which is the most common type of stub axle?
- 6 How does a front axle work?
- 7 What are the types of front axle?
- 8 What is axle drop in a front axle?
- 9 What is the type of section in the end of the front axle?
- 10 What causes an axle to break?
- 11 Does axle damage total a car?
- 12 Is it expensive to fix a broken axle?
- 13 What is the definition of an axle?
- 14 What is a countershaft?
What is the use of stub axle?
A stub axle or stud axle is either one of two front axles in a rear wheel drive vehicle, or one of the two rear axles in a front wheel drive vehicle. In a rear wheel drive vehicle this axle is capable of angular movement about the kingpin for steering the vehicle.
What are stub axles made from?
For maximum strength to weight ratio, a stub axle needs to be forged from steel. Forging will allow the stretched fibres in the steel to follow the lines that will carry load when in operation. You could start with a short round bar. Upset or spread one end to make the flange, while thinning and lengthening the shaft.
What are the symptoms of a broken axle?
Top Signs Your Car Needs Axle Repair Clunking Sounds. If the axle is damaged the vehicle will strain to move. Wheel Area Vibrations. Odd vibrations or an uncommon rumbling sensations coming from the area of one tire that occur as you accelerate or while cornering are good signs that there is axle damage. Car Won’t Move.
What is stub shaft?
These bearing supported stub shafts allow side-load to the back of an engine while simultaneously preventing any load transmission back to the crankshaft. Many industrial engines do not allow side loads on their engine crank shafts (pulley applications) but this is a suitable solution to a common problem.
Which is the most common type of stub axle?
As The Engineers Post explains, there are four types of stub axle: Elliot: This type uses a kingpin, a yoke, and a cotter to connect to the front axle. Reverse Elliot: This type has the opposite arrangement of a standard Elliot stub axle. Lamoine: This stub axle type has an L-shaped spindle instead of a yoke- type hinge.
How does a front axle work?
Modern front -wheel drive cars typically combine the transmission (gearbox and differential) and front axle into a single unit called a transaxle. Each half axle connects to the wheel by use of a constant velocity (CV) joint which allows the wheel assembly to move freely vertically as well as to pivot when making turns.
What are the types of front axle?
There is two types of front axles: (a) Dead front axle, and (b) Line front axle. Dead axles are those axles, which donet rotate. These axles have sufficient rigidity and strength to take the weight. The ends of front axle are suitably designed to accommodate stub axles.
What is axle drop in a front axle?
A dropped axle is a straight front axle that has been altered or built to drop a vehicle’s ride height. This makes the vehicle sit lower and places the front suspension nearer to the ground.
What is the type of section in the end of the front axle?
The front axle uses to carry the weight of the front part of the vehicle as well as to facilitate steering and absorb shocks due to road surface variations. It is made of I- section in center position while the ends are made either circular or elliptical with the construction.
What causes an axle to break?
Axles are rods or shafts that connect to the drive wheels. Even though axles are built to be tough, an overloaded vehicle can sometimes crack or break an axle. Bad carrier bearings or bad potholes are other common causes of axle problems.
Does axle damage total a car?
depends if you crashed when breaking the axle. Normally you just replace the axle and the other front-end components, that should be far less to fix than replacing most cars. A car is considered “totalled” if the cost to fix it exceeds its replacement value in the repaired state.
Is it expensive to fix a broken axle?
The cost to repair an axle runs between about $500 and $600 dollars before taxes and fees. Costs vary depending the type of vehicle, brand, make, and model. Labor costs vary from between about $50 dollars and $140 depending on how long the job takes for a model of vehicle.
What is the definition of an axle?
1a: a pin or shaft on or with which a wheel or pair of wheels revolves. b(1): a fixed bar or beam with bearings at its ends on which wheels (as of a cart) revolve. (2): the spindle of such a beam.
What is a countershaft?
1: a mechanism used to transmit motion and power from a main driving shaft to an individual machine, typically mounted by hangers on a ceiling, and driven by one belt from the main shaft and in turn driving the machine by another belt.