- 1 What is water pump pulley?
- 2 What happens if water pump pulley goes bad?
- 3 How much does it cost to replace a water pump pulley?
- 4 Can you replace the pulley on a water pump?
- 5 Can I drive with bad water pump?
- 6 What noise does a failing water pump make?
- 7 What causes a water pump to go bad?
- 8 What are signs of a bad water pump?
- 9 How long will a water pump last after it starts leaking?
- 10 How long does a water pump take to replace?
- 11 Can you change the water pump without changing the timing belt?
- 12 How long does a water pump last in a car?
- 13 How do you remove a pulley from a water pump?
- 14 How do you remove a pulley without a puller?
- 15 Should a water pump pulley spin freely?
What is water pump pulley?
The water pump pulley on a car helps to provide the power that this part needs to push the coolant through the engine. Every time that your car is cranked, the water pump pulley will have to spin freely in order for the car’s cooling system to work properly.
What happens if water pump pulley goes bad?
Extensive wear on the water pump or serpentine belt If the pulley is loose it can cause the water pump belts to shake and develop more heat. When this occurs, the belts can crack or literally shred; as most of these belts are made out of rubber and nylon cords for strength.
How much does it cost to replace a water pump pulley?
Below are some pulley labels and their respective product offers. Dorman: Water pump pulleys from Dorman are available as OE replacements. Their standard prices range from $33.98 up to $55.77, all with Dorman’s lifetime limited warranty.
Can you replace the pulley on a water pump?
If the water pump pulley is broken or damaged and the water pump is not circulating coolant, heat levels in the engine quickly build up to the point that they can damage your engine. It is essential to get your water pump pulley replaced as soon as possible.
Can I drive with bad water pump?
However, it not advisable to keep driving a car with a bad water pump because it can lead to overheating which will eventually result in complete damage of your car engine. A car with a bad water pump can start and move but, cannot cover much mileage.
What noise does a failing water pump make?
One way to check for worn out or failed water pump bearing; is to check for water pump shaft movement. So, with a faulty bearing, you can often hear a squealing, howling; or sometimes a grinding noise coming from the front of the engine.
What causes a water pump to go bad?
Water pumps can fail prematurely due to corrosion inside the cooling system or from an imbalanced water – pump shaft. But in most instances, water pumps fail because of shaft leaks. Excessive tension on a fan belt or serpentine belt also can overload the water – pump shaft bearings and cause the pump to fail.
What are signs of a bad water pump?
Here are 5 common symptoms of a bad water pump: Coolant Leak at the Front-Center of your Car. Rust, Deposit Buildup, and Corrosion of the Water Pump. Water Pump Pulley is Loose and Making Whining Sounds. Engine is Overheating. Steam Coming from your Radiator.
How long will a water pump last after it starts leaking?
0-50 miles As long as the bearings don’t fail, then I would venture to say that the seal has failed and if it is “fresh” it will probably make 50 miles, just make sure that you don’t heat things up with extra load (extra pressure on cooling system)..
How long does a water pump take to replace?
The range is approximately two to three hours depending on whether your vehicle has power steering and/or air conditioning. It is economical to replace the pump on a mobile basis and you can obtain a repair quote for mobile replacement by referring to YourMechanic’s water pump replacement service page.
Can you change the water pump without changing the timing belt?
Yes you can replace the water pump without replacing the serpentine belt. You will have to remove the belt to replace the water pump anyway. Since you are likely going to have to purchase a new pump, we do recommend that you purchase a belt at the same time.
How long does a water pump last in a car?
A water pump should last 60,000 to 90,000 miles, about the same amount of time as a timing belt. “Many water pumps are located behind the timing cover,” Beckwith says. “It makes sense to replace the water pump when you have the timing cover off and are already that deep into a labor-intensive repair.
How do you remove a pulley from a water pump?
How to Remove a Water Pump Pulley Remove obstacles away from the water pump. Remove the engine’s timing belt or chain if necessary, as this is often in the way of the water pump. Remove the water pump belt from the water pump. Install the pulley removal tool to the water pump pulley. Tighten the removal tool slowly.
How do you remove a pulley without a puller?
There is a way to do it. You put a wrench on the pulley bolt and block the other end against the floor or the frame. Then you use the starter motor to turn the engine (DO NOT START IT, JUST TURN IT) for at most one or two revolutions of the crank. Just enough to break the bolt loose.
Should a water pump pulley spin freely?
New water pump should be nice a tight and not spin freely. Also the rotation should be perfectly smooth. If it feels gritty, it’s bad. Bearings, like the tensioner pulley are the same.