- 1 How do I know if my throttle position sensor is bad?
- 2 What happens when your throttle position sensor goes bad?
- 3 How do you test a throttle body sensor?
- 4 How much does it cost to replace a throttle position sensor?
- 5 Can you drive with a bad throttle position sensor?
- 6 How do you reset throttle position sensor?
- 7 Can a bad throttle body cause transmission problems?
- 8 When I press the gas pedal it won’t accelerate?
- 9 Will a bad TPS throw a code?
- 10 What causes code P2138?
- 11 What causes a throttle body to go bad?
- 12 What should TPS be at idle?
- 13 Does a new throttle body need to be reprogrammed?
How do I know if my throttle position sensor is bad?
Here are some common symptoms of a bad or failing throttle position sensor to watch for: Car won’t accelerate, lacks power when accelerating, or accelerates itself. Engine won’t idle smoothly, idles too slowly, or stalls. Car accelerates, but won’t exceed a relatively low speed, or shift up.
What happens when your throttle position sensor goes bad?
Common signs include lacking power when accelerating, rough or slow idle, stalling, inability to shift up, and the Check Engine Light coming on.
How do you test a throttle body sensor?
How to Test TPS With a Volt Ohm Meter Locate the throttle body. Follow the fuel line to the housing mounted over the block of the engine. Identify the power, ground and signal wires on the TPS. Typically the ground is black, the power is red and the signal wire is a different color, blue for example. Check the reference voltage. Check signal voltage.
How much does it cost to replace a throttle position sensor?
The average cost for throttle position sensor replacement is between $171 and $219. Labor costs are estimated between $59 and $74 while parts are priced between $112 and $145.
Can you drive with a bad throttle position sensor?
Depending on the exact nature of your bad throttle position sensor problem, your car could be very difficult to drive, it could get stuck on the side of the road, or it could even accelerate uncontrollably – a very scary and dangerous situation!
How do you reset throttle position sensor?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
Can a bad throttle body cause transmission problems?
The Throttle Position sensor measures the throttle position, which is controlled by the gas pedal. It is used to determine engine load and if it fails it can cause automatic transmission shifting problems. When a throttle body is not functioning correctly, some noticeable characteristics may be poor or very low idle.
When I press the gas pedal it won’t accelerate?
The most common reasons why your car is having trouble accelerating is due to three main categories: Actuator Malfunction – bad spark plugs, faulty fuel pump, damaged fuel injectors, old fuel wiring, and other fuel component issues.
Will a bad TPS throw a code?
A faulty TPS can set a trouble code in the computer if the voltage value is either not present, sporadic, slow or constant, and this can illuminate your check engine light.
What causes code P2138?
Diagnostic trouble code (DTC) P2138 stands for “Throttle/Pedal Position Sensor/Switch D/E Voltage Correlation.” It is triggered when the vehicle’s engine control module (ECM) or powertrain control module (PCM) detects that the signals from the two throttle position sensors (or two accelerator pedal position sensors) do
What causes a throttle body to go bad?
Filth, carbon, and dirt can build up in the housing creating problems with air flow. Known as coking, the normally smooth service for air to travel becomes full of gunk and creates an imbalance. This interrupts that perfect mixture of air and fuel which can cause the butterfly valve to get stuck.
What should TPS be at idle?
At idle is should be zero or a couple of degrees. Press down on the gas pedal very S-L-O-W-L-Y until the throttle is all the way open. If the TPS has a worn spot, most likely it will be between 0 and 20 percent throttle opening. Try holding the throttle between 0 and 20 percent to see if you get a steady reading.
Does a new throttle body need to be reprogrammed?
In fact, on some engines a new throttle body needs to be programmed with a factory, or equivalent, scan tool. The technician cannot even clean the carbon out of the throttle body in some cases without setting a “check engine” light.