Often asked: Which Valve Spring?

How do I know what valve springs to buy?

Most manufacturers will recommend valve springs to go with each camshaft they make. We recommend the same springs listed by the camshaft manufacturer, or a spring with similar specifications. Understanding the spring specifications will help you select the right springs for your engine.

What do heavier valve springs do?

Higher spring rates mean greater force on the camshaft and consequently more resistance to rotation. The flip side to this argument is that stiffer valve springs control the valves better at high speed and provide better prevention of bouncing valves, which can create more power.

How do I know if my valve spring height is installed?

There are two ways to measure installed height: Using a good mechanic’s ruler, measure the spring from where it meets the bottom of the retainer to where it sits on the cylinder head. DO NOT INCLUDE THE THICKNESS OF THE SHIMS. Use a valve spring height micrometer.

See also  Quick Answer: What Gas Does Lincoln Mkz Take?

Are intake and exhaust valve springs the same?

Are valve springs the same on intake and exhaust valves? Intake and exhaust valves are often different diameters, of different materials, or following different cam profiles, all of which can be factors influencing the size or stiffness of spring required.

What causes valve spring failure?

What Can Cause Valve Springs To Fail. To maintain correct valve operation at normal engine speeds; all of the valve springs must exert a certain amount of spring pressure. Consequently, too low or week valve spring pressure; may cause valves to not completely seal or float under higher (RPM).

When should a valve spring be replaced?

Valve springs should also be replaced if they are out-of-square. If the spring leans to one side more than about 1/32 inch when placed against a 90 degree square, the coils have deformed and the valve spring needs to be replaced.

Do heavier valve springs add horsepower?

We have done A-B-A engine dyno tests, and you do not lose HP with heavier springs. However, too light (seat pressure) can be VERY bad for the valve train, especially the roller lifters themselves.

How do you break in a new valve spring?

To properly break in your newly installed valve springs, run your newly installed valve springs through one heat cycle at a maximum of 1,500-2,000 rpm until the engine warms up and then let your engine cool down.

What happens when valve spring tension is too low?

If spring tension is too light, valve float and eventual engine damage can occur. According to cam experts, one of the most common causes of premature camshaft failure is the use of improper valve springs. This can include too high or too low spring pressure, or the springs can just be plain worn out.

See also  Problem: Does Cadillac Xt4 Have Heads Up Display?

What happens when valve spring tension is too high?

If the spring pressures are too high, the added friction will result in: More heat, Faster valvetrain wear, Potential failure of other valvetrain parts (i.e. rocker arms, pushrods, etc.), and.

Can you have too much valve spring pressure?

Yes, too much spring pressure will damage parts. As you have seen first hand. Too much seat pressure will collapse lifters and cause valves to float as well.

How long do valve springs last?

How Long do Valve Springs Last. Valve springs can last a long time, but they do wear. On higher mileage engines with 100,000 miles or more, it is not uncommon for the valve springs to lose tension. Springs that have lost more than 10% of their tension should be replaced.

How much does it cost to replace a valve spring?

The cost of this replacement job will be between $900 and $1,800, depending on the make and model of your vehicle. The process of replacing valve seals involves disassembling the entire engine until you can reach the valve spring.

Are both valves closed at TDC?

Power stroke. The piston is at top dead center, intake and exhaust valves are both closed and the spark plug has just fired. The exhaust valve opens fully and starts to go closed. Before the piston reaches TDC, the intake valve starts to open and the exhaust valve is still partially open.

What happens when a valve spring breaks?

Broken valve springs cause excessive valve noise, compression loss and can cause severe internal engine damage. Actions following the breaking cause the most serious damage to the engine. When spring breaks, it may collapse just enough to allow the valve to drop into the cylinder, where the piston may strike it.

Leave a Comment