- 1 Where is the throttle body position sensor located?
- 2 What are the signs of a bad throttle body position sensor?
- 3 How do you change a throttle position sensor on a Chevy Silverado?
- 4 What will a bad throttle position sensor do?
- 5 How do you reset throttle position sensor?
- 6 How much does it cost to fix throttle position sensor?
- 7 Can a bad throttle body cause transmission problems?
- 8 Can you drive with a bad throttle position sensor?
- 9 How do you test a throttle position sensor?
- 10 Does a new throttle body need to be reprogrammed?
- 11 Will a bad TPS throw a code?
- 12 How do you reprogram a throttle position sensor?
- 13 How do I reset my electronic throttle control?
Where is the throttle body position sensor located?
A throttle position sensor ( TPS ) is a sensor used to monitor the air intake of an engine. The sensor is usually located on the butterfly spindle/shaft, so that it can directly monitor the position of the throttle.
What are the signs of a bad throttle body position sensor?
Here are some common symptoms of a bad or failing throttle position sensor to watch for: Car won’t accelerate, lacks power when accelerating, or accelerates itself. Engine won’t idle smoothly, idles too slowly, or stalls. Car accelerates, but won’t exceed a relatively low speed, or shift up.
How do you change a throttle position sensor on a Chevy Silverado?
Step 1 – Remove the air intake hose. Open the hood and use a flat head screwdriver to loosen the hose clamp on each end of the air intake hose. Step 2 – Gain access to the TPS. Attach a 15mm socket with ratchet and extension to the center bolt of the tensioner pulley. Step 3 – Remove the TPS. Step 4 – Install the new TPS.
What will a bad throttle position sensor do?
Common signs include lacking power when accelerating, rough or slow idle, stalling, inability to shift up, and the Check Engine Light coming on.
How do you reset throttle position sensor?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How much does it cost to fix throttle position sensor?
The average replacement cost for the throttle position sensor is anywhere from $110 to $200. The parts cost is anywhere from $75 to $105 while the labor cost is anywhere from $35 to $95. In addition, you will have to account for any extra fees and taxes that get added on as well.
Can a bad throttle body cause transmission problems?
The Throttle Position sensor measures the throttle position, which is controlled by the gas pedal. It is used to determine engine load and if it fails it can cause automatic transmission shifting problems. When a throttle body is not functioning correctly, some noticeable characteristics may be poor or very low idle.
Can you drive with a bad throttle position sensor?
Depending on the exact nature of your bad throttle position sensor problem, your car could be very difficult to drive, it could get stuck on the side of the road, or it could even accelerate uncontrollably – a very scary and dangerous situation!
How do you test a throttle position sensor?
How to Test TPS With a Volt Ohm Meter Locate the throttle body. Follow the fuel line to the housing mounted over the block of the engine. Identify the power, ground and signal wires on the TPS. Typically the ground is black, the power is red and the signal wire is a different color, blue for example. Check the reference voltage. Check signal voltage.
Does a new throttle body need to be reprogrammed?
In fact, on some engines a new throttle body needs to be programmed with a factory, or equivalent, scan tool. The technician cannot even clean the carbon out of the throttle body in some cases without setting a “check engine” light.
Will a bad TPS throw a code?
A faulty TPS can set a trouble code in the computer if the voltage value is either not present, sporadic, slow or constant, and this can illuminate your check engine light.
How do you reprogram a throttle position sensor?
Make that the accelerator pedal is completely released or free, then turn “ON” ignition switch and wait for 3 seconds. You want completely depress the accelerator pedal very hard and fully release the accelerator pedal as quickly as possible 5 times within 5 seconds.
How do I reset my electronic throttle control?
Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.